Author Topic: What type of saw chain do you use (Read 2514 times)

T Welsh · « **on:** October 18, 2011, 06:26:00 am »

I am curious about what type of chain every body is using on there saws
my favorite is 72lgx Oregon square chisel full comp. I also use Stihl rapid rsc full chisel. Tim

Cut4fun · « **Reply #1 on:** October 18, 2011, 06:40:50 am »

I still have rolls of oregon CL real square chisel full comp 3/8 and RS RSK RSC round chisel, oregon LG 325 and 325 RSC, then PS3 3/8LP

JHBC · « **Reply #2 on:** October 18, 2011, 10:37:29 am »

On my Stihls 20"-28", I use Oregon 72LGX, and my Huskys 32"-42", I use Oregon 68LX or 68JX. Full chisel, but not square.

John Mc · « **Reply #3 on:** October 18, 2011, 12:46:47 pm »

"square" chisel would be the Oregon 72CL. (the tooth is sharpened with a square-edge file, rather than a round file.) Gives a bit of extra cutting performance over "round ground" chisel chain, but tougher top sharpen by hand. I've only used one once, on a GOL instructor's saw, just to see what it was like.

The 072lgx is a round chisel chain You sharpen it with a round file, but the "corner" of the tooth (where the top plate meets the side plate) is still square, rather than rounded off or chamfered like a semi-chisel (or "micro-chisel") chain.

I use either the 073lgx or 073lpx (the 073lgx is just the .058 gauge version of the 072lgx. Don't ask me why, but just about everyone around here seems to use .058 gauge chains.) The lpx has a bit more anti-kickback provisions in the design (but is still nothing like the worthless consumer safety chain). To tell you the truth, I can't tell the difference between the two when cutting. When running .325 pitch, I've used Oregon's 21LPX chain (round chisel, a .325 pitch version of 72LPX)

I've also used Bailey's "Woodland Pro" chain: 28RC for the .325 pitch, and 38RC for .375 pitch chain. Both are round chisel, seem to cut similarly to the Oregon chain. I've heard this is just re-badged Carlton/Total. (6 or 7 years ago I did have some Carlton chain that had hard spots in it that ruined a few raker files, but I've never run into the problem since.)

If I recall, the sharpening angles on the Woodland Pro chain are a bit different from the Oregon... and it did not like being sharpened to Oregon specs.

nmurph · « **Reply #4 on:** October 18, 2011, 03:59:31 pm »

Quote from: T Welsh on October 18, 2011, 06:26:00 am

I am curious about what type of chain every body is using on there saws
my favorite is 72lgx Oregon square chisel full comp. I also use Stihl rapid rsc full chisel. Tim

LGX is not square chisel. It is chisel, but not square filed chisel; that would be CL

BobR · « **Reply #5 on:** October 18, 2011, 05:07:35 pm »

Stihl RMC (yellow) chain works great on my MS 261 with 16" bar.
Oregon 90S (non safety) works great on my pole saw. Bailey's sells this by the link. I've not seen it advertized anywhere else.

mad murdock · « **Reply #6 on:** October 18, 2011, 05:14:06 pm »

I run chisel tooth full skip chain on my 372XP, I cut mostly Doug Fir, and it cuts like butter, the hardwood I do cut, is mostly big leaf maple, and it cuts easy as well. When I mill I use the woodsman pro ripping chain that Bailey's sells. On my smaller saws I use semi-skip semi-chisel (half round), as it can take the dirt better, and since I use the smaller saws for alot of the dirtier cutting, that works best for me. I have run Carlton, Wlindsor, Oregon, Woodsman Pro, they all seem similar. I don't see much of a difference between chains, they all seem pretty good, as long as they are set up properly, they all cut great.

mooleycow · « **Reply #7 on:** October 20, 2011, 08:12:43 pm »

I bought a stihl farm boss ms290. After reading the post here I get the idea the green chain on my saw is a product liability chain. Think after reading I may need a rsc yellow chain. New here, don't use one much, except hurricane cleanup. Used to live in the mountains(meadows of dan Virginia) cut my share. You folks are right on about helping people you meet to learn about cutting wood. Thanks for being here.

beenthere · « **Reply #8 on:** October 20, 2011, 08:24:07 pm »

Not sure why you think that, or how you think that. How is it a product liability to you?

AdkStihl · « **Reply #9 on:** October 20, 2011, 08:26:30 pm »

Stihl .325 RSC on the MS270WB , .404 RSLF on the 08 & Oregon S-series 91 Low Profile Chamfer chisel on the Eager Beaver.

T Welsh · « **Reply #10 on:** October 20, 2011, 08:59:47 pm »

Quote from: mooleycow on October 20, 2011, 08:12:43 pm

I bought a stihl farm boss ms290. After reading the post here I get the idea the green chain on my saw is a product liability chain. Think after reading I may need a rsc yellow chain. New here, don't use one much, except hurricane cleanup. Used to live in the mountains(meadows of dan Virginia) cut my share. You folks are right on about helping people you meet to learn about cutting wood. Thanks for being here.

Most of the chains on this topic are pro chains with little or no kick back features, be aware that if you change your (green tie strap) chain for (yellow) you will be increasing cutting,but you will also increase kick back, be safe and look into whats right for you and your saw, if your cutting mostly firewood go with a chipper type chain they are more forgiving than chisel chain when you hit the dirt (we all do it) Tim

Al_Smith · « **Reply #11 on:** October 20, 2011, 10:19:50 pm »

I can't rememeber the numbers but most times it's some form of round chisel chain usually Oregon , except the antiques .Those if they are gear drives is whatever they came with . They're for show not to cut much wood with .They will of course but at a somewhat "relaxed " pace .

acco1840 · « **Reply #12 on:** October 20, 2011, 10:49:21 pm »

Stihl full chisel. anything else is crap.

Al_Smith · « **Reply #13 on:** October 22, 2011, 11:08:45 am »

Stihl is good chain ,no doubt but it should be for the price .

Oh sure it's harder and might last longer but it will still break cutters and bend drivers just like all the rest .

Chain is just like oil which I won't get into .You have people lining up on both sides of the line to argue or evangelise about any brand made .Funny thing is they all seem to be able to cut wood .

T Welsh · « **Reply #14 on:** October 22, 2011, 05:59:44 pm »

Al. I second that!!! The sharpest,cheapest chain works for me. we go through a 100' reel a year and it would more if we didnt keep it the ties straps under lock and key. our guys have habit of trashing chains

Tim

Al_Smith · « **Reply #15 on:** October 23, 2011, 07:52:29 am »

Well you know I try to refrain from getting anal about chain ,saws ,oil or politics .Although sometimes just because of the orneriness within me I like to stir the pot just a little .

I'll never bad mouth Stihl chain with the exception of anti kick back .On that I'll opinionate on anybodys safety chain .Then again although it's not for me I can see were some feel it's safer and that's fine .

I personally think Oregon micro chisel is a faster cutting chain than Stihl chisel but again that's just an opinion . Now don't get me wrong because I've got plenty of Stihl chain loops .If I were in the business of using a chainsaw to make a living I'd probabley use more of it but I'm not so I don't .

Pricey stuff but I hear through reliable sources that in areas of the PNW they sell it in competitive prices with Oregon which here amongst the corn fields they do not .

Then again Lawdy what has happened to the price of chain now days ? I about had sticker shock when I looked up the price through Baileys for a either a 105 or 109 driver loop of .404 chisel for an 084 .It wasn't so long ago I bought 143 driver loop for about half what it sells for today .

Just Me · « **Reply #16 on:** October 25, 2011, 07:15:52 pm »

I buy up those "Al Gore" safety chains as the old fellow I buy them from calls them as he will not sell a chain saw with them on. He's an old farmer selling Dolmars in his retirement, and it you need a lesson in right wing politics... Whew!

Anyway... Those chains are great for cutting into houses and doing log work just because they do not cut too aggressively, they do not pull into the cut. They also seem to be able to hit more nails and keep working, probably because they do not allow a big bite. I screw them up and throw them away. He sell them to me for $5 brand new, so why sharpen? Faster than a sawzall for sure......

On my XP I am thinking of trying a skip tooth. My buddy has one on his and says it cuts hardwood firewood faster, but he's just a carpenter like me. Can someone fill me in on a skip tooth and when you should use it? I'm in the dark.

Larry

Al_Smith · « **Reply #17 on:** October 25, 2011, 07:50:52 pm »

Al Gore didn't have a thing to do with safety chains ,that was Ralph Nader .He was also famous for stopping production for few years of convertable automobiles ,Corvairs and just about anything that could be used in a dangerous way to hurt one another .In other words because he felt that we collectively weren't smart enough to protect ourselves from ourselves the government should do it for us .

The only thing Al Gore is famous for is inventing the internet plus supposidely being an ultra conserative eco type guy while all long having a 10 thousand dollar a month electric bill .Evidently he and Tipper must have disagreed .

Just Me · « **Reply #18 on:** October 26, 2011, 05:45:29 am »

Al, to this old guy, and if you met him you couldn't help but like him, Al Gore represents everthing that is wrong with this country.

Hence his "AL Gore" chains.

He cracks me up every time I am there......

Larry

roadiestar · « **Reply #19 on:** February 07, 2012, 06:32:54 pm »

What ever is on sale

News:

Author Topic: What type of saw chain do you use (Read 2514 times)