Pole Saw

[Good Feller]

I'm wanting to get a gas pole saw.  Any recommendations?  I'd like one with a 10-14" bar.  I'm going to use it for my forestry business.  I want something good,,, no junk.  Thank you. 

[beenthere]

I've had excellent service from my Stihl HT75
Not sure that model is still available, but it's never let me down.

Go to a dealer you like to work with, as there are other good brands, I'm sure.

[Rocky_J]

The ht75 is no longer made. Stihl has the ht101 and the ht131. The 131 is a little stronger, a little heavier and about $50 more expensive. They are the '4-mix' technology, a 4 stroke motor design that uses mix gas like a 2 stroke. The valves need to be adjusted at about 150 hours. They don't rev as high but they have more torque.

If you're going to use this professionally, don't even bother thinking about anything but the Stihls. Nobody else comes close as far as the power polesaws are concerned. Call up the 20 biggest tree services in your area and ask them which brand/ model they use. At least 19 of them will say "Stihl".

And I'm not just a Stihl cheerleader. The only Stihls I own are the HT101 and a few MS200Ts. All my other saws are Husqvarnas, two 346XPs, three 372XPs and a 395XP.

[WDH]

Most people in the logging woods around here use Stihl pole saws to trim their trucks loads before hauling.

[rebocardo]

> If you're going to use this professionally, don't even bother thinking
> about anything but the Stihls.

I agree, I don't own one because I really can't justify the cost and one of my main uses is for cutting free blown over trees where I want to stand 12 feet away and take the chance on killing the saw instead of me.

I have borrowed various gas powered pole saws. The Stihl was the heaviest and the best. The aluminum pole feels very solid when you are using it.

[liketocut]

I have only used (2 years) Stihl HT101.
I think it's worth every penny. I'm no pro,
between Dad and I we have just over 600 acres
of fence and field edges to keep trimmed
Cuts good and starts easy, cold or hot.

[Al_Smith]

 The HT 75 is longer being made,as was already said . Coincidently ,just a week or so ago I worked on one with a bend shaft,something quite common on these things and a real challange to repair I might add .

My personal pole saw is an inexpensive Poulan .While it's not nearly the quality of a Stihl it does just fine for the stuff I do .Further more you can buy about 3 of these these things for the price of just one Stihl . It only has an 8 or 10 inch bar though but that will get just about anything short of lopping a 12 inch  limb from a big oak which you wouldn't normally do with a pole saw any way .

[olyman]

i just bought a like new ht75---the reason i bought a stihl--because it has the longest extension--almost 12 foot--the others dont---and im not a stihl person--but you got to do what you got to do------

[thecfarm]

I was kinda looking for one I think last year.The one I wanted was a removable power unit so I would not have to buy a bunch of motors too.Stihl was the only one that offered this feature.I should say that I felt was worth it to look at.Probaly more  by now do this.One comes up with an good idea and they all copy it.

[Al_Smith]

 The Poulan is 12 feet also but it's not adjustable ,you get all 12 at once . Like I said though it's not nearly the quality of the Stihl but then it doesn't cost as much either .It all depends on what you want I guess

[sawguy21]

The Kombi system thecfarm mentioned is increasingly popular. The only downside is lack of reach. It is not telescoping although a 3 foot extension is available.

[cheyenne]

check out the husky it will reach out 16' and the balance is great & cuts like a dream runs about $550 great for working in blowdowns & limbing. cheyenne

[D._Frederick]

I  have a fixed shaft Husqy that is a pleasure to use, it has plenty of power to get a 5inch limb. I have had nothing but problems with the bar oiler, cost me $80 to replace the pump. It had a valve in it that would not work and I could not take it apart to clean.

[uwharrie]

I'm wanting to get a gas pole saw.  Any recommendations?  I'd like one with a 10-14" bar.  I'm going to use it for my forestry business.  I want something good,,, no junk.  Thank you. 

I , just like most of the others would recommend the Stihl HT131. It has plently of power and it's priced right. The HT131 has a more powerful engine than the HT101 for only 50 bucks more. 

[sawguy21]

The HT131 also has an extra bearing in the tube to prevent the shaft from whipping at full extension. A number of our customers run the Kombi hedge trimmer attachment on it (with the short shaft removed) and it works well. There were shaft failures on the HT101 when used this way because of vibration.

[olyman]

The HT131 also has an extra bearing in the tube to prevent the shaft from whipping at full extension. A number of our customers run the Kombi hedge trimmer attachment on it (with the short shaft removed) and it works well. There were shaft failures on the HT101 when used this way because of vibration.

  ok, so heres the question---can that bearing be mounted in the ht75 i just bought??? ---as i dont need a shaft failure in mine---as i know stihl parts get mighty expensive---

[Al_Smith]

  ok, so heres the question---can that bearing be mounted in the ht75 i just bought??? ---as i dont need a shaft failure in mine---as i know stihl parts get mighty expensive---
[/quote] The HT 75 uses a kind of plastic tube on the upper portion on the shaftway .That part of the shafting is round .The lower section is splined and runs in three bearings .The center one is floating ,held on center by two counter opposing springs .

According to the local Stihl dealer it costs about as much to replace the shafts and tubing as it would to buy a new unit .This is why I straightened out my buddys saw for him ,at least it works now .

[Good Feller]

So what is the procedure when you get the bar pinched 16ft off the ground???  I don't have a ladder that tall or a boom truck,,,, hence why I'm wanting a pole saw in the first place. 

I like Al Smith's logic.  I could buy 3 poulans for the price of one Stihl.  An 8 inch bar should cut through most situations.  I'm pretty sure I don't want to cut 12 inch limbs 16ft off the ground anyways.  $500-$600 bucks for a pole saw is a big hit to the wallet.  If one poulan takes a crap you have 2 more as back up.  Nobody likes poulan but my smallest chainsaw is a poulan woodshark and I like it.  I keep it cleaned up and maintained,,, it is a good saw for the price.  I'm leaning towards the poulan. 

[Rocky_J]

In that case get the Poulan. That isn't what you asked for in your initial post. You said you wanted something of high quality, no junk. You asked for something with a 10-14" bar. The Stihl models are high quality, no junk, with a 12" bar. But you gotta pay for them. If you want cheap, then go buy whatever they sell at Home Depot. The clerks there can assist you. 


This is why I quit offering saw advice here 3 years ago. Looks like it's time for me to quit posting again.

[cheyenne]

in your original post you said no junk. now your saying i can buy 3 pieces of junk for the price of quality & safty. I have the perfect solution for you. GET A BEAVER & A WOODPECKER